Openbox s9 hd pvr satellite receiver: 九月 2014

2014年9月1日星期一

How to Solder an LED Bulb

Light emitting diodes (LEDs) are quickly becoming one of the most efficient sources of light. Their long-lasting life, coupled with their low power consumption, proves them to be a very effective light source for the home and other places. If you want to create your own LED lights, you can solder the bulbs yourself.

Instructions
1
Prepare the soldering iron for use. Whether you have a new soldering iron or you are using an old one, you will need to "tin" the tip of the soldering iron by coating it in solder. Plug in the soldering iron and allow it to heat up. Coat the entire end of the soldering iron with solder, which will allow the solder to transfer to your project more smoothly later.

2
Prepare the surface of the circuit board. Clean the surface of the circuit board using a Scotch Brite pad. This will rid the surface of any dirt or impurities and provide a clean surface for the solder to stick to.

Place the LED on the circuit board. Insert the two leads from the LED into the pre-drilled holes in your circuit board, in the location where you want to have the LED. Bend the ends of the two leads slightly, from the bottom side, to prevent the part from falling over while you solder it.

4
Solder the LED in place. Heat one lead of the LED with your soldering iron. Do not touch the tip of the soldering iron to the solder directly. Touch the tip of the solder to the LED and allow the heat from the lead to melt the solder into the connection joint. Allow a small pool of solder to appear at the base of the lead, which will hold the LED in place. Allow this connection to cool for a few minutes and complete the other side the same way.

5
Inspect the joint. Ensure that the solder has fully connected the LED to the circuit board and that there are no loose connections. If you find a loose connection, simply reheat that soldered joint until the old solder melts. Remove the old solder from the joint with a wet rag and re-solder the connection.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

dm8000 hd dreambox dm8000 dm 8000 hd dreambox 8000 dreambox dm7020 dm7020 HD dreambox 7020 dm7020 HD dreambox 7020 Dreambox dm800 HD Se dm800 hd se with Wifi dm800 hd pvr dreambox dm800 hd pvr cheap dreambox dm800 hd pvr http://www.dreamboxok.com/dm500si.html Dreambox dm500S satellite receiver http://www.dreamboxok.com/Dreambox-DM-500-S.html DreamboxDM 500 OEM http://www.dreamboxok.com/DM500-OEM.htm Dreambox DM500C http://www.dreamboxok.com/Dreambox-DM-500-C.html Dreambox DM500C OEM http://www.dreamboxok.com/dm500c-oem.html Dreambox DM500S OEM http://www.dreamboxok.com/dm500s-oem.html Dreambox DM500Si Silver http://www.dreamboxs.com/dm500si.htm Dreambox dm500Si black http://www.dreamboxok.com/dm500si-black.htm Dreambox dm 518S http://www.dreamboxs.com/dreambox-dm518s.html Dreambox DM500T http://www.dreamboxok.com/Dreambox-DM-500-T.html AzBox HD Elite

How to Synchronize LED Lights With iPod Music

Lights that blink on and off in time with music are often used by dance clubs to excite the crowd. To create your own "light show" with the music coming from an iPod, use a music sync device. There are a number of these devices available from computer and electronics stores, and even hobby shops. These devices all work in a similar manner to control the illumination of lights in time with audio. Those that include LED lights as part of their makeup eliminate the need for any assembly work whatsoever. An audio speaker, however, will also be needed (e.g., an iPod music dock) in order for the iPod's music to be heard.

Instructions
1
Place the music sync device on a table. Stretch out the LED light modules attached to the music sync device so that they form an irregular pattern on the table. Plug the music sync device's power cord into a wall socket for power. Press the music sync device's power button to turn it on and supply power to the LED lights.

2
Place the speaker dock on the table. Plug its power cord into a wall socket for power. Insert the iPod into the speaker dock's iPod connector.

Aim the front of the music sync device, which contains the built-in microphone, toward the front of the speaker dock.

4
Press the power button on the speaker dock to turn it on. Press the "Menu" button on the iPod to bring up the menu. Select "Music" from the menu. Scroll down the list of choices on the screen and select a playlist. Press the "Play" button to begin playing songs from the playlist.

5
Press the "Volume +" button on the speaker dock to increase the audio volume. Continue increasing the audio volume until the LED lights of the music sync device begin to blink.

6
Adjust the fine-tuning knob on the music sync device to control the speed and intensity of the light's blinking. Turn the room lights off and enjoy the light show as the music plays.

Tips & Warnings
Music sync devices that rely on being plugged in to independent LED lights must not exceed the rating for the AC power of the device.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

How to Build a Grow Box With LED Lighting

Growing your own plants at home can be even more productive when you get them to grow inside in an organic grow box. With the advent of bright light emitting diodes, or LEDs, you can add intense light close to your seedlings without burning the plants. The construction of a grow box basically involves using a structure large enough to house your plants with extra space for air ventilation.

Instructions
1
Line a large box or plastic storage container with sheets of aluminum foil. Use a few beads of craft glue along the inside of the box to hold the foil in place. The foil will reflect more of the light around the plants than a box without foil.

2
Place a shallow tray in the bottom of the box to hold drainage water. This makes it easier to water the plants and keeps the bottom of the grow box clean.

3.Set your soil-free filled plant pots onto the tray, while leaving enough space between the plants for good air circulation.

4
Attach two rows of high-intensity white LED light strips to the bottom of the cover of the grow box. Some strips come with pre-attached adhesive while others require a few screws to keep them in place. Drill a hole through the side edge of the cover with a drill. To keep the hole small, drill the hole as large as the width of the cord and slice from the hole to the edge of the cover. Pry open the slit with a utility knife to slide your plug through.

5
Place the cover over the organic grow box. Plug in the LED lights to test. Remove the cover. Plant your seeds, add water and nutrients as needed per plant. Replace the cover on the box, turn on the LED lights and wait for the plants to sprout.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

How to Find If an LED Tail Light Meets Department of Transportation Standards

One of the key difficulties in car modification and repair is ensuring that your car is "street legal"--that is, it complies with all the standards and regulations for cars implemented and enforced by the U.S. Department of Transportation. Even a non-standard tail light can mean that your car can be taken off the road. With careful examination, however, ensuring your LED tail light meets government standards is a simple process.

Instructions
1
Go to an automotive parts store and examine the tail light you would like to install. The packaging will be clearly marked if the tail light is approved by the federal Department of Transportation. Also examine it for signs that it is a counterfeit part; such signs include misspellings on the packaging, bad grammar and incorrect contact information for the company. If you find signs of a counterfeit part, or no sign of DOT approval, assume it is not approved and investigate other brands until you find one that is DOT-approved and has no signs of counterfeiting.

2
Examine the specifications of the tail light and compare them to your state's specifications for tail lights. While it is likely the government and the state have very similar requirements, there may be subtle differences that may disqualify the light. If possible, ask to see a demonstration model of the part, or ask if there are cars at the shop with this tail light already installed so you can see it in action.

3
Install the tail light, and then test it to make sure it performs to both federal and state standards. Turn the wheel to the direction it is signaling in to see if it shuts off. Time the light to ensure it is not flashing too quickly, which may be a safety hazard for epileptic drivers. Ensure the light turns on and turns off smoothly with the use of the turn signal, and that it has been wired to the turn indicator on the dashboard. Look at the light at night and ensure it is bright enough to be seen but not bright enough to dazzle other drivers.

Tips & Warnings
Use only reputable auto parts dealers and installers. For local dealers, check sites like Yelp to find out more about their reputation and business. Local and national dealers will likely carry parts that meet state and federal standards.

Log on to the website of the company you are considering buying a tail light from. The site should note the part is DOT approved.

Counterfeit car parts are a major risk. If you have any suspicion that a part is counterfeit, do not install it.

Never install a car part yourself unless you know exactly what you are doing. If you are uncomfortable or uncertain, have a professional install it for you.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

How to Connect Power LED to a Motherboard

The power light emitting diode is a small light diode installed on the front panel of the computer case. If connected to the motherboard, the power LED lights up steady green when the computer is turned on, and starts to blink or lights in yellow when the computer goes into sleep mode. This LED is not important for the computer's functionality, but it allows you to easily identify if your machine is in sleep mode.
Instructions
1
Switch off the computer and disconnect the power cord on the back panel.

2
Open the computer case by removing the side panel. Then lay the computer on its side. Note that the motherboard is attached to the opposite side panel with screws.

3.Look for the system panel connector cluster that is in the bottom right corner of the motherboard. This cluster includes at least five different connectors, including a power switch, reset, a case's speaker, power and hard drive LEDs.

4
Consult the motherboard's manual and find out which pins in the cluster correspond to the power LED connector. The manual will have a scheme on which the polarity ("+" and "-") of the connection is marked.

5
Locate a computer case cable that goes from the power LED. This cable has a connector on the end that would fit into the pins on the motherboard.

6
Touch the metal surface of a large object to discharge static electricity before doing any work with electronic parts such as the motherboard. For example, touch an unpainted metal part of the computer case.

7
Insert the connector of the power LED cable into the corresponding pins (see Step 4) on the motherboard using a gentle force.

8
Close the computer case and power up your machine.

Tips & Warnings
Static electricity can severely damage the motherboard and other computer components. This damage is not covered by the manufacturer's warranty.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

How to Replace an LED Cat Eye Bike Light

Cat Eye LED bike lights are mounted on both the front and back of your bike so you can ride safely at night. These bike lights are easily replaceable should one of yours ever fail or should you just want a different model light. Learning how to replace a Cat Eye LED bike light can help you insure that your bike is equipped with everything it needs to keep you safe.

Instructions
1
Remove the light from the bracket fastened to your bike by pressing the red button located on one of the sides of your light to release it. You should be able to pull it forward gently and hear it click out of place. Don't try to force it if you intend on keeping the bracket.

2
Unscrew the dial on the bracket strap fastened to your bike and remove the light. You'll want to take this with you to purchase a new light to insure that the new light will fit in your bracket. If you know the bracket model and number, then you can leave it on the bike.

3.Purchase a Cat Eye LED light to fit the bracket you have on your bike. If you have an older model, you may have difficulty finding a light that fits, but ask the salesclerk if he can suggest a replacement.

4
Refasten your bracket around the front or back bars on your bike with the dial facing inward, looping it around the bar and back through the slot under the dial. Turn the dial clockwise to fasten. Slide your light into the bracket from the side opposite the dial until you hear a click that indicates it is locked in.

Tips & Warnings
Always read all instructions and safety warnings that accompany any new light you buy prior to installing the light onto the bike.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

How to Trim Home LED Net Lights

How to Trim Home LED Net Lights

Decorating the outside of your home with LED net lights for Christmas, or any other occasion, has many advantages over trimming your small trees and shrubbery with traditional string lights. Net lights are pre-configured to be evenly spaced when hung, as opposed to aligning string lights which takes a lot of time to space properly. You can purchase LED net lights in various lengths, enabling you to cover large portions of your home's exterior with ease.

Instructions
1
Unfold the LED net lights on a flat surface and spread them out so that you can easily see all of the lights.

2
Plug the power chord into an electrical outlet. Inspect the lights for any lights that do not light or other defects in the net. LED lights rarely burn out, but it is easier to know if there is a problem before you hang the lights.

3.Unplug the power chord and move the lights to the desired location. Locate the nearest electrical outlet. If there is no outlet readily available, use an extension cord long enough to reach the outlet. Make sure that the extension cord is rated for outdoor use.

4
Grasp the top edge of the net lights with both hands. Drape the net over the bush or other object. Arrange the lights so that the entire object is covered.

5
Plug the net lights into the outlet or extension cord. Inspect the lights and rearrange the net if desired.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

How to Solder a LED Light for Your PC

Proper soldering requires practice. Soldering a light emitting diode (LED) or any other device to a printed circuit board (PCB) takes skill and patience, especially on modern boards with tiny connections. You should not try it on your first attempt at soldering. Practice on something else first. Mistakes can be costly. But once you feel up to the task, follow the steps carefully. Make sure you have a low power soldering iron that will not burn adjacent components, and you use solder with a small diameter not to flood the PC board with excess solder which may cause a "bridge" (short circuit).

Instructions
1
Clean the circuit traces on the PC board with solvent and a clean rag.

2
Insert the two leads on the LED into the designated holes on the PC board. Observe proper polarity; the anode being positive or plus and the cathode, negative or minus.

3.Bend the leads away from each other at a 45-degree angle from the plane of the circuit board. This holds the LED in place while your solder it.

4
Plug the soldering iron in and let it heat up.

5
Clean the soldering iron tip by melting solder onto it. Quickly wipe it clean on the damp sponge. It should be bright and shiny. If it is not, keep cleaning it until it is.

6
Touch the soldering iron to one of the leads of the LED where it touches the PC board trace. When it is hot, in a few seconds, touch the tip of the solder lightly to the joint but not to the soldering iron. The solder will melt quickly and "sweat" onto the joint. Quickly pull the iron and solder away. A good solder joint will look shiny.

7
Repeat step 6 for the other lead on the LED.

8
Snip the excess leads off with the wire cutters. Cut them flush with the PC board.

9
Clean the solder joints with a rag dampened with the solvent. Then dry it with a dry rag.

Tips & Warnings
Turn your equipment off and unplug it before starting. Working on energized equipment is dangerous to both you and the equipment.

Be careful that your soldering iron does not touch other components or solder joints on the PC board.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

How to Make Light-up Shirts

Stitch a row of LED lights onto the shoulder, sleeves or front pocket of a shirt to make it light up and stand out. You will take your crafting to the next level once you learn how to work with soft circuits and conductive threads. You can start with a pre-made button-up shirt or T-shirt, or sew your own shirt and then attach the lights to it. Sewing a switch into the shirt lets you turn the lights on and off.

Instructions
1
Position your shirt on the embroidery hoop. Drape the part of the shirt that you will add the lights to over the inner circle of the hoop, then push the outer circle over top. Pull the shirt tightly and tighten the screw at the top of the hoop to secure the shirt.

2
Arrange the LEDs in a row or pattern (such as a circle or flower shape) on the shirt. Once you've determined how you want the lights to look, mark where each light will go with a disappearing ink marker.

3.Thread the needle with the conductive thread. Tie a knot in the opposite end of the thread.

4
Use the needle-nose pliers to bend the long lead (the metal wire that sticks out of the bottom) of each LED into a square, coiling the wire all the way up to the base of the light.

5
Use the pliers to coil the shorter lead of each LED up to the base of the light. Coil each lead on the switch, as well.

6
Position the first LED on the shirt and hold it in place with your fingers.

7
Push the needle up through the shirt, coming from the inside. Stitch around the square coil of the LED and push the needle back into the shirt. Continue to stitch around the square-coiled lead, until it is securely fastened to the shirt.

8
Place the battery holder on the inside of the shirt, near the first LED. Sew from the first lead of the LED to the positive end of the battery holder. Stitch around the positive end (there should be a small metal loop) until it is securely attached to the shirt.

9
Stitch from the positive end of the battery holder to where you will place the next LED. Sew the square-coiled lead of the LED to the shirt in the same manner that you sewed the first LED. Repeat, attaching the square coils of the remaining LEDs.

10
Tie the conductive thread at the end, to secure it. Wrap the thread under itself, so that it does not unravel and short circuit. Cut the end of the thread.

11
Re-thread the needle if you need to and tie the end of the thread. Push the needle up through the shirt and stitch the rounded coil lead of the first LED to the shirt. Make sure you do not touch the thread used to sew the positive, squared leads with the thread you are using to sew the negative, round leads. Stitch the remaining rounded leads in place. Do not tie off and trim the thread.

12
Cut a small hole in the shirt and push the switch through it, keeping the wire leads on the inside of the shirt. Stitch one lead to the shirt, using the same thread you used to sew the negative LED leads in place. Tie off and cut the thread.

13
Re-thread your needle and knot the end. Stitch the second lead of the switch in place, the same way you sewed the LED leads.

14
Stitch from the second lead on the switch to the negative end of the battery holder. Sew the negative end of the battery holder in place, then knot the thread end and trim.

15
Turn the switch so that the battery holder is off. Insert the coincell battery into the holder. Flip the switch and watch your shirt light up.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

How to Educate a Technician to Install LED Lights

The performance of a well-trained technician can be appreciated by his clients. When his clients call upon him, he is expected to thoroughly fix their problem. Educating a technician on how to install LED lights may be a challenge at first, but once understanding is established the technician will have little problem installing LED lights.

Instructions
1
Inform the technician that the first step in installing LED light involves drilling holes into the vehicle's body away from extreme heat and moving components. Such heat can damage the LED light by increasing its current flow. This preventive step involves marking the proper drilling and mounting location, usually above the headlight housing. In addition, drilling above the headlight housing allows the technician to avoid other significant damage to electrical lines, fuel lines, brake lines and exhaust systems (Reference 1).

2
Have the technician test the headlight housing needed for mounting the LED light tubes. A good idea is to completely remove the headlight housing and install the brackets for mounting first (Reference 2). After this the technician must drill with accuracy, penetrating straight down and quickly out. The hole should be no wider than necessary. A wide or crooked hole will allow moisture or dust to eventually enter the headlight housing. Apply a bit of silicon sealer to the holes to prevent rust.

3.Show the technician how to locate the automobile's fuse box underneath the hood. Once this is accomplished the technician should access and insert the LED's red power wire in the headlight nearest to the fuse box (Reference 2). The headlight furthest away from the fuse box should be in sync with the illuminating diode with ground connector. Continue installation by inserting one of the LED wires and grommet. Pull up on the wires in order to position the LED near its entrance hole. However, the wire should not be visible. In many states there is a law against this.

4
Show the technician how to connect ground so that a sufficient source of power can be accessed later (Reference 2). Ground components can consist of a quality, medium-sized bolt with a metal ground blade underneath. This mechanism should not be excessively tight, otherwise it could crack or break apart. A ground connector is very significant. Without it, very high current can damage the LED lights.

5
Have the technician strip insulation from the end of the LED light's red power wire up to approximately 1/8 or 1/4 inch (Reference 2). Have him probe the head light with the red wire, contacting one of the two small metal tabs until the LED lights come on. These tabs can be found atop each fuse. Once power is discovered the technician can remove the fuse.

6
Direct the technician to insert the stripped wire into one of the two slots once occupied by the fuse. The appropriate slot should result in the illumination of the LED light while the other slot should not produce a similar result (Reference 2). The fuse should be reinserted after this to keep the power wire from moving. The LED light should be fully illuminated. The second LED should be installed in the same manner as the first. Insert it into the headlight housing along with a push plug. This finishes the installation process.

Tips & Warnings
When training a technician to install LED lights, encourage him to thoroughly read the installation instructions. This will cause him to become more grounded as well as confident (Reference 2). Having prior knowledge before performing an installation job makes following direction much easier and saves the trainer and trainee valuable time. Installing LED lights is not as difficult as it sounds. All it takes is a little patience while acquiring knowledge and experience.

To avoid injury and damage to the technician, he should disconnect the negative battery cable. Read the vehicle's service manual to learn more about the automobile's electronic system (Reference 2). Disconnecting the entire battery can cause the electronic system to malfunction on some modern cars. Therefore, it is wise to only disconnect the negative battery cable instead the entire battery.

dm8000 hd wholesale led light usb flash drive usb flash drive wholesale usb flash drive flash drive manufacturer led lighting LED Wall Wash light LED video pixels LED Digital Tube light LED Spot Light LED Point Light LED Under-ground Lighting LED Commerical Lighting LED ba?ador de pared LED píxel de luz Tubos LED luz llevada del punto LED punto de Luz lenovo cellphone LED Spotlights Buried LED Iluminación Comercial Мытья стены СИД света Светодиодные видео пикселей Светодиодные трубки

Power supply for DM500C DM500S DM500T

Remote control for DM600PVR DM7000 DM7020S DM7025

Power Supply for DM600PVR DM7000 DM7020S DM7025

订阅：评论 (Atom)